The sawing machine drive system adopts servo control and gear rack transmission to ensure smooth operation, and the large sawing speed of Zui can reach 85m/min.According to different sawing widths, it can automatically position the sawing stroke, reduce the idle stroke time and improve the working efficiency.The worktable is made of pneumatic float, which can effectively prevent the plate from scratching and make the plate move more easily.The main saw and auxiliary saw adopt independent lifting

　Today, Gaomi Dongyu Machinery will share with you the precautions for CNC panel saws at work, hoping to help you. CNC panel saws can be used for vertical and cross-cutting of various wood-based panels such as veneer particleboard, fiberboard, plywood, solid wood board, plastic board, aluminum alloy and other materials. It is widely used in panel furniture industry and wood processing industries such as vehicle and ship manufacturing. , belongs to the general equipment among woodworking machinery, and the market demand is relatively huge. However, the following points should be noted in the work: 1. When cleaning the machine tool, rubbing lubricating oil, disassembling and replacing saw blades and removing wood chips, the power must be cut off first. 2. When a fault occurs, the power supply should be cut off immediately, and the operation should be stopped, and the repair and adjustment should be carried out by a special person. The machine tool is not allowed to run with faults. 3. B

Today, Gaomi Dongyu Machinery will share with you the preparations for the start-up of the CNC panel saw, hoping to help you. 1. Check whether the power switch of the CNC panel saw is pushed in place, and whether there is a phase loss in the current, so as to avoid burning the machine motor due to the lack of phase when the machine is activated. 2. Clean up the machine table and workplace. When operating the CNC panel saw, the person who starts the machine must keep his legs straight and his body straight, and cannot lie down or lean on the operating platform. 3. Check whether the saw blade of the CNC panel saw is perpendicular to the sliding table, and whether the large and small saw blades are on the same straight line. Test the machine for about one minute to see if the CNC panel saw operates normally. 4. Push the push bed several times first to check whether the slide rail is smooth. Keep the slide rail clean and smooth. 5. Prepare the materials and accessories.

Today, Gaomi Dongyu Machinery will share with you the four major preparations before the operation of the CNC panel saw, hoping to help you. 1. First, clean up the machine and workplace. 2. Next, check whether the vacuuming system is normal. 3. Then check whether the push table saw blade is sharp and whether the size saw blade is in a straight line. Test the machine for about a minute to see if the machine runs normally. 4. Then prepare the materials and accessories.

The CNC panel saw has the characteristics of easy operation, stability and safety, and is an essential equipment for the batch, standardized, mechanized and specialized production of furniture. The CNC panel saws produced abroad and in Shenyang are more adaptable and stable to use, and their precision meets the cutting requirements of solid wood and composite panels. The CNC panel saw absorbs the international advanced technology and adopts the unique domestic design to manufacture. It is used for precision cutting of wood, various veneer, wood-based panels and aluminum alloys. CNC panel saws are used for longitudinal, cross-section or angled sawing of plywood, particleboard, fiberboard, veneer, laminate, blockboard, spliced solid wood and plastic panels to obtain dimensional compliance Plates required by the specification, and also

(1) Turn on the power switch and start the system start button on the computer operation panel (2) Put the workpiece on the lifting table and reset the safety baffle switch (3) Enter the password to enter the CADMATIC production interface (4) The machine starts at this time Initialization, when the automatic die, feeding device, saw blade system, etc. no longer flash, the following operations can be performed (5) According to the situation, select the function key F2, F3, F4 or F5 to select the sawing method (single-piece sawing, Die cutting, manual sawing, etc.) (6) When performing manual sawing drawing operation, you can input the sawing drawing name and number correctly according to the interface prompts, or press INS to select the saved drawing. (7) After the sawing diagram is set, press F11 to input the sawing diagram. (8) Monitor the number of stacks, the status of the automatic mold, the speed of the saw blade and whether the current of the saw blade is in good condition.

When using and operating these cutting equipment, you must follow the specifications, otherwise it will affect normal production. 1. Safety protection requirements (1) Dust masks must be worn. (2) No loose clothes, uniform work clothes, and bracelets are strictly prohibited. (3) The saw blade must be equipped with protective devices. 2. Key points of safe operation (1) Before operation, check whether the control switch of the panel furniture cutting machine is sensitive, and whether the safety grating and emergency stop switch are in normal state. (2) Before starting the machine, check that the saw blade of the machine is clean, sharp and free of defects, whether it is locked, and whether the direction is correct. (3) When the machine is sawing, it is forbidden to open the safety protection curtain, observe or touch. (4) Non-professionals or professional maintenance personnel of the machine are strictly prohibited from operating the operating system without permission, modifying or add

Today, Dongyu Machinery will share with you the five major characteristics of CNC woodworking tenon and groove machine equipment: 1. The tenon and groove machine equipment is used for mortising, grooving and drilling of doors, tables, chairs and other products. Second, the size and length of mortise processing can be input and processed on the computer side, which is convenient and fast. 3. The reducer adopts the reducer imported from Japan, the control of acceleration and deceleration is reasonable, the stability of the processing stroke is good, and the use accuracy is guaranteed. 4. One equipment adopts 2--3 stations to process in turn, and the man-machine cross work mode to improve work efficiency. 5. It can process 6 pieces at one time, which greatly saves time and labor.